If a new component would be installed, there are procedures for that which you need to bear in mind. The procedures have to be followed to install Profile Design Cobra bars properly. That is also a requirement on the policy for the warranty that is provided when you buy one. When you are now knowledgeable on such task, go to its dealer near the area.
They have a manual which contains all of the steps you must do. If you will just do that on your own, you should prepare all of the tools that are needed for this. You must have an Allen or torque wrench. You must also have some sandpaper as you are going to use that to make it smoother. If you have all of what you needed then you could now start on that.
The clamping area must not be greased. When a person is going to grease that part, this will cause that bar on slipping from the area. One must ensure that he will be avoiding that kind of situation particularly during the time that he will use that bike. While riding that bike, you might be losing control of it. Your safety cannot be assured when such situation occur.
You have to make sure that the diameter of the bar clamp would match to the diameter of its stem. This should be checked so that you could avoid any problems with it. It would not fit if their diameter would not be the same. Before you would buy, you have to check the diameter so you would not waste your money on buying one.
If you are installing the stem that is new, there are still some instructions from the manufacturer that you should read. Some steps have been set by a manufacturer so you can be certain that it is correctly done. It is indicated on their manual so they can provide that on you so you will not find it difficult on how you can start with that.
You should check the front stem clamp if there are any sharp edges. Use the sandpaper that you have so that they would be removed. You have to do that as it would damage the fiber of the aluminum or carbon. Once you have placed it on its position, you could now clamp it on the stem. You have to make sure that it is tight.
You should slide the lever to the bar. If it makes you uncomfortable, you should adjust it depending on what you want. You have to place it carefully. You have to remember that if it would be broken, it would affect the warranty of the material.
You may wrap that if you like. If you will be trying that, you should be certain that you would wear a helmet. Check that it will work well before it will be used on traveling places that are far.
It is essential that those steps will be followed. This will be risky on you as you will lose your control on that bike. It could cause worst injuries on a person.
They have a manual which contains all of the steps you must do. If you will just do that on your own, you should prepare all of the tools that are needed for this. You must have an Allen or torque wrench. You must also have some sandpaper as you are going to use that to make it smoother. If you have all of what you needed then you could now start on that.
The clamping area must not be greased. When a person is going to grease that part, this will cause that bar on slipping from the area. One must ensure that he will be avoiding that kind of situation particularly during the time that he will use that bike. While riding that bike, you might be losing control of it. Your safety cannot be assured when such situation occur.
You have to make sure that the diameter of the bar clamp would match to the diameter of its stem. This should be checked so that you could avoid any problems with it. It would not fit if their diameter would not be the same. Before you would buy, you have to check the diameter so you would not waste your money on buying one.
If you are installing the stem that is new, there are still some instructions from the manufacturer that you should read. Some steps have been set by a manufacturer so you can be certain that it is correctly done. It is indicated on their manual so they can provide that on you so you will not find it difficult on how you can start with that.
You should check the front stem clamp if there are any sharp edges. Use the sandpaper that you have so that they would be removed. You have to do that as it would damage the fiber of the aluminum or carbon. Once you have placed it on its position, you could now clamp it on the stem. You have to make sure that it is tight.
You should slide the lever to the bar. If it makes you uncomfortable, you should adjust it depending on what you want. You have to place it carefully. You have to remember that if it would be broken, it would affect the warranty of the material.
You may wrap that if you like. If you will be trying that, you should be certain that you would wear a helmet. Check that it will work well before it will be used on traveling places that are far.
It is essential that those steps will be followed. This will be risky on you as you will lose your control on that bike. It could cause worst injuries on a person.
About the Author:
Read more about Procedures On Installing Profile Design Cobra Bars You Must Follow.
No comments :
Post a Comment